@

max

Thursday

How to replace Oil Pump on 2008 Honda Odyssey?

Oil pump replacing procedure for Honda car model is as follows :-----
Oil Pump 

Inspection



Specific to:
Honda Odyssey 2007-2008
  1. Remove the screws from the pump housing, then separate the housing and cover.

    Click image to see an enlarged view
    Fig. Check the inner-to-outer rotor radial clearance between the inner rotor (A) and outer rotor (B)
  2. Check the inner-to-outer rotor radial clearance between the inner rotor (A) and outer rotor (B). If the inner-to-outer rotor clearance exceeds the service limit, replace the oil pump assembly.
Inner Rotor-to-Outer Rotor Radial Clearance:


Standard (New): 0.04-0.16 mm (0.002-0.006 in.)
Service Limit: 0.20 mm (0.008 in.)

Click image to see an enlarged view
Fig. Check the housing-to-rotor axial clearance between the rotors (A) and pump housing (B)

  1. Check the housing-to-rotor axial clearance between the rotors (A) and pump housing (B). If the housing-to-rotor axial clearance exceeds the service limit, replace the oil pump assembly.
Housing-to-Rotor Axial Clearance:


Standard (New): 0.02-0.07 mm (0.001-0.003 in.)
Service Limit: 0.12 mm (0.005 in.)

  1. Check the housing-to-outer rotor radial clearance between the outer rotor (A) and pump housing (B). If the housing-to-outer rotor radial clearance exceeds the service limit, replace the oil pump assembly.

    Click image to see an enlarged view
    Fig. Check the housing-to-outer rotor radial clearance between the outer rotor (A) and pump housing (B)
Housing-to-Outer Rotor Radial Clearance:


Standard (New): 0.10-0.19 mm (0.004-0.007 in.)
Service Limit: 0.20 mm (0.008 in.)

Removal & Installation



Specific to:
Honda Odyssey 2007-2008
  1. Drain the engine oil.
  2. Turn the crankshaft so that the No. 1 piston is at top dead center.
  3. Remove the timing belt.
  4. Remove the idler pulley.
  5. Remove the crankshaft position (CKP) sensor A/B.
  6. Attach the chain hoist to the engine hanger on the power steering (P/S) pump bracket.
  7. Remove the jack from under the oil pan.
  8. Remove the rocker arm oil control solenoid (VTEC solenoid valve)/oil filter assembly (J35A6 engine) or oil filter base/oil filter assembly (J35A7 engine).
  9. Remove the oil pan.
  10. Remove the oil screen.
  11. Remove the mounting bolts and the oil pump assembly.

    Click image to see an enlarged view
    Fig. Oil pump and related parts-J35A6 engine


    Click image to see an enlarged view
    Fig. Oil pump and related parts-J35A7 engine
To install:
  1. Remove the old oil seal from the oil pump.

    Click image to see an enlarged view
    Fig. Gently tap in the new oil seal until the oil seal driver bottoms on the pump
  2. Gently tap in the new oil seal until the oil seal driver bottoms on the pump.
  3. Remove all of the old liquid gasket from the oil pump mating surfaces, bolts, and bolt holes.
  4. Clean and dry the oil pump mating surfaces.
  5. Inspect both rotors and pump housing for scoring or other damage. Replace the parts, if necessary.
  6. Apply liquid thread lock to the pump housing screws, then install the oil pump cover.
  7. Check that the oil pump turns freely.
  8. Apply liquid gasket, P/N 08717-0004, 08718-0001, 08718-0002, 08718-0003, or 08718-0009, evenly to the engine block mating surface of the oil pump.
    NOTE
    Do not install components if too much time has passed after applying the liquid gasket (for P/N 08718-0002, no more than 4 minutes, for all others, no more than 5 minutes). Instead, remove the old residue and reapply liquid gasket.
  9. Grease the lip of the oil seal, and apply oil to the new O-ring (A).
  10. Install the dowel pins (B), then align the inner rotor with the crankshaft, and install the oil pump (C). Clean the excess grease off the crankshaft, and check the seal for distortion.
  11. Install the oil screen with new O-ring (E).
  12. Install the rocker arm oil control solenoid (VTEC solenoid valve)/oil filter assembly, with a new rocker arm oil control solenoid filter (VTEC solenoid valve filter) (J35A6 engine), or oil filter base/oil filter assembly, with a new O-ring.
  13. Install the oil pan.
  14. Install the crankshaft position (CKP) sensor A/B.
  15. Install the idler pulley.
  16. Install the timing belt.
  17. Remove the engine hanger.
  18. After assembly, wait at least 30 minutes before filling the engine with oil.


------------
This details will help you.
----------
If you need dis-assembly or replacement instructions for any other auto/car part, or you want to ask question related to your car/truck jeep problem then please leave the comment with your details, so I can provide you the required instructions and solutions.

------------

For your help, there are few Car Engine oil related solved problem listed 

below. You can go through it.

Low oil pressure light on Dodge Magnum? 
http://howtobyme.blogspot.com/2011/11/low-oil-pressure-light-on-dodge-magnum.html 

Kia Sportage leaking oil from oil pan? 
http://howtobyme.blogspot.com/2011/11/kia-sportage-leaking-oil-from-oil-pan.html 
Car Turns OFF due to low oil pressure warning light?


For more oil and oil pump details check out the direct links below: --- 
Oil pressure for 2001 gmc jimmy V6? 


How to replace Oil Pan on 2008 Honda Odyssey?


How to replace Oil Pressure Sensor on 2008 Honda Odyssey?



No comments:

Post a Comment

@